Latest news on Manufacturingtalk categorised by product type
Drives, motors and power transmission, couplings, clutches
Archive page 31 of 69
Our RSS feed for Drives, motors and power transmission, couplings, clutches press releases
Protect your valuable drive and control software
Factory managers can now protect their companies against the costly consequences of software loss thanks to the introduction of a drive and control software back-up service.
News from Bosch Rexroth (31 May 2005)
Polyurethane timing belts reduce run-off
A range of endless polyurethane timing belts combine higher tooth-pitch accuracy with a novel bifilar, S and Z wound, steel tensioning system, which greatly reduces belt run-off.
News from Transmission Development Co. (GB) (30 May 2005)
Motor Guide keeps AC users up-to-date
A 130-page Motor Guide informs users about the general installation and maintenance advice relating to AC motors and outlines the standards and designs used.
News from ABB Automation Technologies (Drives and Motors) (20 May 2005)
Linear motor escalates food packaging speeds
User application article High-speed, dual-forcer linear motor powers food packaging system that attaches zips to a continuous plastics web at 120 pouches/minute and allows a higher fill ratio. Brochure available
News from Baldor UK (16 May 2005)
Drive and automation system embraces all
A drive and automation system represents a complete system solution which embraces motors, geared motors, servo drives and field devices such as I/O and remote maintenance modules. Brochure available
News from Lenze ( 9 May 2005)
Drives 'intelligence' takes over system control
Technical background article Drive-based automation, in which intelligence is built into decentralised drives, enables them to replace motion controllers and/or PLCs and includes safety functions, reports Lenze. Brochure available
News from Lenze ( 9 May 2005)
Compact low-cost stepper driver launched
A low cost driver for two- and four-phase hybrid stepper motors is a compact bipolar microstepping unit providing a maximum resolution of 12,800 steps/revolution.
News from Astrosyn International Technology ( 9 May 2005)
Drives can replace soft starters
Component drives are small, simple, low-cost drives used to control a wide range of equipment and can replace other components such as contactors and soft starters.
News from ABB Automation Technologies (Drives and Motors) ( 5 May 2005)
Check up on your belt drive practices
Technical background article Belt drives are a prime example of an overlooked area where other gains in efficiency can either be wiped out or enhanced, says Bryan Burton, who explains there are savings to be made. Brochure available
News from Wyko Industrial Services ( 3 May 2005)
Regenerative motors are not complex
Using little panel space and mounting on standard DIN rail, drives are able to regenerate energy back into the mains supply under braking without the need for complex intermediate storage.
News from Sprint Electric ( 3 May 2005)
Drives provide ferequency converter functions
Due to the consistent decoupling of performance and functions, the a drive series provides both hardware-based servo drive and frequency converter functions.
News from Bosch Rexroth ( 3 May 2005)
Better protection provided for bigger motors
Controllers provide versatile motor protection that can be matched to the application and offer cost-saving integrated inputs and outputs for control functions as well as communications.
News from Schneider Electric (27 April 2005)
Synchronous motors earn ATEX approval
Hazardous duty synchronous motors with a flameproof enclosure satisfy ATEX standards for use in potentially explosive atmospheres as defined by CE directive 94/9/EC.
News from Danaher Motion (25 April 2005)
Nanometric control eliminate motor 'rumble'
Nanometric control eliminate motors' mechanical 'rumble' and provide ultra smooth very low-speed motion down to microns/s as well as no rotating parts and virtually zero inductance.
News from Micromech (22 April 2005)
CD speeds in-line planetary gearhead selection
CD enables engineers and designers to identify the correct in-line planetary gearhead by entering performance requirements, specifying motor dimensions or entering model number. Brochure available
News from ZF Great Britain (20 April 2005)
AC drives have modular expansion bus
Advanced adjustable speed AC drives feature a modular expansion bus and option range that allows users to configure optimum solutions for every AC drive application. Brochure available
News from Baldor UK (19 April 2005)
SS induction motors are reliable under wash-downs
Stainless steel enclosed AC induction motors are available in eight standard frame sizes and provide reliable operation when subjected to frequent wetting or washdown.
News from Empire Magnetics (19 April 2005)
Couplings reduced in size by 33%
Optimised disc springs and the use of new wear-free materials has allowed couplings in to be reduced in size by 33% without compromising performance. Brochure available
News from Tandler Precision (15 April 2005)
Single wire connects servos to controllers
Wash down servo system's motor and encoder signals route through the single, round, connector to servo controller/drivers, producing a simple installation.
News from QuickSilver Controls (11 April 2005)
Integral motor gear unit is 'plug and play'
Integral motor gearbox unit is designed to provide the benefits of automation while retaining the convenience of manual speed control in tough working environments. Brochure available
News from Wyko Industrial Services ( 6 April 2005)
Earlier news from this category...
Latest news from this category...
