Product category:
Drives, motors and power transmission, couplings, clutches
News Release from: ABB Automation Tech (Drives and Motors) | Subject: Fans
Edited by the Manufacturingtalk Editorial
Team on 12 October 2004
£100k a year saved on a single fan
ABB equipment installed for just £20k is saving over £100k a year at Salt Union's plant in Runcorn, Cheshire
ABB equipment installed for just £20k is saving over £100k a year at Salt Union's plant in Runcorn, Cheshire Replacing a single oversized fan with a smaller version equipped with speed control has cut the energy consumption on one of the plant's dryers by over 60 per cent
This article was originally published on Manufacturingtalk on 28 Jun 2002 at 8.00am (UK)
Related stories
Insulation manufacturing process saves energy
Some GBP 50,000 worth of energy is being saved per year, since existing variable speed drives for cooling fans were replaced on an insulation forming conveyor.
Variable drives save costs for kiln fans
A bathroom-ware manufacturer is set to save GBP 14,000 per year following installation of variable speed drives following the results of an energy audit on its two firing kilns.
Salt Union has a flowsheet capacity of producing a million tonnes of salt every year at the Runcorn site.
As well as food grade pure dried vacuum salt, the plant also produces a courser granular product as well as tablets.
The dryer in question processes a coarse, granular product used in applications such as dishwashers.
Further reading
Low voltage high speed motors into production
ABB is beginning production of low voltage high speed motors, which will have applications including compressors, fans, pumps, testing rigs and the aeration systems within wastewater treatment plants
Standard drives designed for immediate use
A new range of intuitive, easy-to-use standard drives, designed to be sold off-the-shelf with few optional extras, is targeted at standard applications, such as pumps, fans and conveyors.
The previous fan sucked air through the dryer at a rate controlled by a damper in the pipeline.
During normal operation, this damper was 95 per cent closed so most of the fan's energy was being used to suck the air through the narrow constriction.
An energy survey by ABB Drives Alliance member Central Electrical was carried out to determine what potential savings could be achieved.
The original fan motor was rated at 337kW, but Central Electrical's calculations showed that 132kW should be enough to create the draft needed by the dryer.
"That's a huge energy saving when you think we run the unit for about 8000 hours a year," says Electrical Plant Improvement Engineer Dave Mullin.
"In fact, it equates to over 1.6GWh/y." The old fan was replaced by a smaller version from Fan Systems of Halifax, equipped with a 132kW four-pole motor coupled to an ABB industrial drive.
The resulting energy savings now average a staggering £9000 a month.
The original fan was badly oversized for historical reasons.
The dryer was previously used to process vacuum salt crystals, which are much smaller than the spherical, 2-3mm diameter particles in granular salt.
The fine crystals created a far bigger pressure drop across the dryer than today's coarse product.
"The fan was probably on the generous side to start with.
Years ago it was common for engineers to add a safety margin," says Mr Mullin.
"But once the duty changed it became grossly oversized." It's a common problem, according to Ken Tym of Central Electrical: "Industries and processes change, but there are a lot of areas that manufacturers don't seem to consider.
Sometimes it's about re-educating end users about the energy savings that are achievable." At Salt Union, energy-saving initiatives aren't confined to the process.
Even the small amount of waste heat now produced by ABB's variable speed drive is being put to work warming up the switch room in winter.
"It's not a major saving but it's good to be using a waste product in this way," says Mr Mullin.
• ABB Automation Tech (Drives and Motors): contact details and other news
• Email this article to a colleague
• Register for the free Manufacturingtalk email newsletter
• Manufacturingtalk Home Page
Search the Pro-Talk network of sites
