Product category:
Monitoring and sensor equipment and systems
News Release from: Flintec UK | Subject: CPB aluminium planar beam
Edited by the Manufacturingtalk Editorial
Team on 13 November 2002
Load cells offer potential for filling
machines
A new concept in single point load cells is set to bring significant changes to the design of low capacity weighing equipment.
A new concept in single point load cells is set to bring significant changes to the design of low capacity weighing equipment The CPB aluminium planar beam from Flintec overcomes important design criteria which have hitherto not been addressed by load cell manufacturers
This article was originally published on Manufacturingtalk on 5 Mar 2002 at 8.00am (UK)
Related stories
Universal SS S-beam cells suit harsh environments
Fully welded, stainless steel, universal tension/ compression S beam load cells can be used in a wide range of applications including hopper-, over- head-track-scales and packaging equipment.
Alternative to SS load cells costs less
A low cost, low profile, beam load cell is mechanically interchangeable with existing fully welded stainless steel beam cell and similar industry standard products.
The single point (or moment insensitive) load cell has been around for more than 30 years and is now well proven and accepted for use in bench scales, counting scales, postal scales, retail scales, checkout scales, medical scales, hopper scales, belt weighers -the list goes on.
Their design offers: Simpler scale design; Elimination of flexures; High performance; Wide range of capacities; Low cost; and good environmental protection.
The principle of operation is very simple.
Further reading
Low profile load cell could prove useful
Flintec is introducing a low cost, low profile, stainless steel shear beam load cell which offers exciting design possibilities for a wide range of weighing applications
3D models of off-the-shelf telescopic slides
Telescopic ball bearing slide designer and manufacturer, Accuride International, has produced optimised 3D models of its 'off-the-shelf' products which can be downloaded via its website.
Full digital set-up on tension control system
A new digital tension controller is claimed to be one of the most comprehensive tension control systems currently available
Instead of using multiple load cells (one at each corner) or a single load cell and flexures, one dual or triple beam cantilever load cell is located centrally in the scale and the platform or weighing structure is secured directly to the top of the load cell.
The design of this type of load cell resists torsional loads created by the load being placed off centre.
During manufacture, the flexures are manually adjusted by filing or grinding, in such a a way that wherever a load is placed on the platform, the output from the load cell remains the same.
Although the single point was originally designed for low capacity scales in relatively clean environments, developments in sealing technology, material of construction and capacity range have significantly extended the use of this product.
Fully weld sealed IP68 stainless steel single point load cells up to 1000 kg capacity are now available which can accommodate platform sizes of 1000 x 1000 mm.
However,despite the developments in these areas, two important design criteria have, until now, eluded manufacturers.
Low capacity single points typically suffer from poor side to side stability and offer only a narrow mounting surface for the platform.
The flexures themselves are very thin, making the units susceptible to mechanical damage.
In parallel, attempts to design low profile products have floundered around a height of 20 mm.
The design of the Flintec CPB not only provides an extremely low profile - down to less than 8 mm for the 3-15 kg versions, but also offers a very wide mounting surface.
The CPB has two flexures in the same horizontal plane, rather than above each other in the vertical plane.
The mounting surfaces between these flexures measure approximately 60 x 65 mm and have four, rather than the customary two fixing holes.
This provides a very stable base for fixing platforms, small hoppers, conveyors or other structures.
Even in the 3 kg version, the CPB flexures give excellent mechanical strength and excellent side to side rigidity, allowing platform sizes of up to 350 x 350 mm to be used.
These design criteria make the CPB particularly suitable for low profile bench scales, checkout scales, baby scales and postal scales, as well as small hopper scales and filling machines.
• Flintec UK: contact details and other news
• Email this article to a colleague
• Register for the free Manufacturingtalk email newsletter
• Manufacturingtalk Home Page
Search the Pro-Talk network of sites
