Product category:
Rolling mills and equipment
News Release from: HepcoMotion | Subject: PDU2 belt driven linear transmission
Edited by the Manufacturingtalk Editorial
Team on 30 October 2007
Compact double acting belt drive chosen
A double-acting version of a belt driven system was chosen by an aluminium coil rolling mill for its speed, response and compactness for a limited mounting space.
A double-acting version of a HepcoMotion profile driven unit (PDU2) belt driven linear transmission is demonstrating high performance and cost efficiency at an aluminium coil rolling mill in Conwy, UK Dolgarrog Aluminium is an independent and fully integrated rolling mill that prides itself on flexibility, good service and on-time delivery
This article was originally published on Manufacturingtalk on 26 Jun 2008 at 8.00am (UK)
Related stories
Screw jacks are corrosion resistant
Screw jacks are c orrosion resistant for lifting of any load under chemical or moisture conditions or where hygienic and contaminant-free operation is wanted.
Universal linear motion system offered
A universal linear motion system offers a wide range of sizes, types and precision grades to meet most automation application needs.
Short lead times, low minimum order quantity and bespoke products are its speciality.
Based in North Wales the company's capability is not limited to aluminium.
Investment in a wide range of plant allows it to roll a variety of metals such as alloys of zinc and magnesium.
Further reading
Heavy handling, and pick and place linear motion
HepcoMotion has developed the Hepco HDS range of linear motion solutions for heavy handling and pick and place applications.
Conveyor belts steam cleaned automatically
Food manufacturers can now realise substantial costs savings on the labour-intensive process of conveyor belt cleaning using a system that now automates the task.
Anti-friction guidance mechanisms expanded
The DualVee Motion Technology (DMT) range of anti-friction guidance mechanisms offered by HepcoMotion has been the subject of further development to extend its application potential.
The DAPDU2 belt driven system is used on the company's four-high cold finishing rolling mill.
It receives aluminium coils that are approximately 800mm in diameter at a strip thickness of between 5-8mm.
After several passes the material is reduced to its desired finish gauge that is upwards of 0.5mm.
This process can generate loads of 1400 tons at up to 150m/min.
* Mill upgrade - a recent upgrade introduced a new system to ensure the coil or strip enters the rollers centrally to within +/-5mm of the centreline of the mill.
As Dolgarrog products are available in a variety of widths an automatic sequence was required to maintain productivity and it was for the resultant mechanism that the DAPDU2 system was specified.
The coil centring system comprises the DAPDU2 actuator that spans the width of the in-going side of the mill, two reflecting lasers mounted on each carriage and two pull wire encoders.
The coil centring sequence is activated once the strip has been fed into the mill and is stationary.
The drive is responsible for bringing the lasers in from the edges of the mill at a speed of 100mm/s, whilst the encoders measure the distance travelled; full stroke for each carriage is approximately 500mm.
Once the lasers detect the edge of the strip either simultaneously or independently the measured encoder travel for each side is transmitted to the control.
The software automatically calculates the offset between the two edges and the error value is determined.
This information is then fed back to the decoiler heads that are automatically adjusted via hydraulic rams to rectify the coil position to +/-2mm.
The finishing process then continues.
The HepcoMotion belt driven system was chosen by Dolgarrog for its speed and response and because its physical size was sufficiently small for the limited mounting space available.
And as it has proven, said HepcoMotion to Manufacturingtalk, that the sound performance of the DAPDU2 has been unaffected by its fairly hostile operating environment of kerosene oil mist.
Central to this linear system is a slotted and highly robust aluminium beam of one-piece construction into which fits the belt drive and two carriages.
The arrangement effectively seals the unit on three sides offering it protection in tough conditions.
The carriages use Herculane wheels that run virtually friction-free on the inside surface of the profile yet still provide stable support.
Without motivation, even a light load on the system would accelerate under gravity on an incline of just 8mm/m.
The carriages are driven by a strong and accurate toothed belt that allows them to move symmetrically or together.
"This capability was central to our application," explained project engineer, Mark Jones, in a report to Manufacturingtalk.
"The option to request a total length and stroke length for the system was also very appealing.
The price and delivery lead time for the DAPDU2 fitted well into our plans".
Installed during December 2006, the DAPDU2 is working well and suffered zero downtime.
The entire auto-centring sequence on the four-high cold mill occupies just 6s allowing the operator to continue his production duties during this quality procedure. Request a free brochure from HepcoMotion ...
• HepcoMotion: contact details and other news
• Email this article to a colleague
• Register for the free Manufacturingtalk email newsletter
• Manufacturingtalk Home Page
Search the Pro-Talk network of sites
