Product category:
Non Destructive Testing
News Release from: Inseto (UK) | Subject: High power Viscom X-ray system
Edited by the Manufacturingtalk Editorial
Team on 12 July 2004
Helicopter rotor gear X-ray work is a
partnership
In the critical inspection of helicopter rotor gear, an OEM sought not only the latest X-ray system technology and reliability, but a working partner too.
One of the most important safety relevant components in a helicopter is the rotor gear "The material, as well as all connections such as welds, must be in a perfect state in prior to further processing
This article was originally published on Manufacturingtalk on 3 Aug 2004 at 8.00am (UK)
Related stories
Vapour phase processed PCBs can be solder reflowed
Solder reflow ovens for medium to high volume applications allow PCB assemblies, which so far could be processed only in vapour phase units, to be solder reflowed using forced convection.
WEbsite dedicated to adhesives products
Dedicated adhesives website covers all the latest adhesives technical data on the Delo adhesive range - and equipment - within an easy-to-navigate framework.
For this reason, all of these critical steel parts together with all welds must be tested for any possible material or production faults using a non-destructive method", explained Frederic Cance, Chef de Projets at Groupe SNEF, cooperation partner at Eurocopter.
If a fault occurs on the shaft or another transmission component, a crash would be inevitable.
The test results are documented individually, checked and kept on file for 30 years.
Further reading
Range of manual fine wire bonders
The Microelectronic Equipment Division of Inseto has introduced TPT's new range of manual fine wire bonders in the UK and Ireland.
Fast and accurate NDT speeds production lines
The constant demand from customers for 'best quality', combined with the increasingly competitive nature of the marketplace, has accelerated the development of test methods.
Textile materials testing service expanded
A greater range of textiles testing services are now available from a UK test house following an investment programme that included the purchase of a new Tinius Olsen H5KS testing machine.
For 10 years, Eurocopter has used microfocus X-ray technology for inspection.
They recently decided to purchase a new high power Viscom system for up to 225 KV.
It was necessary to fulfill the following requirements: * Reliable X-ray inspection of extremely thick-walled metal and synthetic cast parts.
* Extremely good image quality providing exact images and thereby ensuring recognition of the smallest details.
* Archiving of the images for 30 years in the form of individual printouts.
* Short exposure time suitable for larger production lots.
Together with SNEF, which is a competent and recognized cooperation partner of Eurocopter, all-important worldwide suppliers of X-ray equipment were reviewed and evaluated.
The excellent cooperation between all three companies, Eurocopter, SNEF and Viscom as well as the high standard engineering and build was finally the decisive factor for purchasing a Viscom system.
- The aerospace sector places high demands on inspection equipment.
In the area of X-ray technology, we were also looking for a technically first-class solution capable of meeting the high demands of the company in terms of the safety and quality of the products.
On the other hand, it was just as important to ensure that the supplier is a competent partner in the area of inspection technology in order to allow flexible reaction and implementation of customer specific adaptations at any time.
"In other words, Eurocopter was not only looking for good equipment but also for a good partner", according to Bernard Peltereau from Viscom France.
Jean-Marc Mercadal, Quality Laboratory < NDT, Eurocopter added: "We were in contact with all important X-ray suppliers and performed many tests and evaluations to study the technical specifications and ensure that we found the best solution.
The cooperation with Viscom and SNEF fulfils all our requirements.
After 6 months use, the excellent cooperation with SNEF and Viscom has shown that this decision was correct." Eurocopter uses a Viscom microfocus X-ray system up to 225kV.
This high tube voltage is required to ensure the enormous X-ray penetration of the thick walled metal parts.
Additionally the high tube power is necessary for short film exposure times required in mass production.
The powerful and even high resolving Viscom microfocus X-ray tubes discern the smallest details.
A special requirement at Eurocopter: X-ray inspection with rod anodes is used, for single wall penetration of nearly closed hollow parts at high energies.
In order to inspect the thick walled steel parts, which are closed all the way around at extremely high radiation energy levels, direct beam as well as the panoramic beam characteristics are used.
For this application the rod anodes are inserted e.g into a gear shaft, in order to X-ray the part from the inside to the outside.
Using a panoramic technique, the X-ray beam radiates the part in 360deg to provide an image of the entire object to be tested.
The X-ray image is projected onto an X-ray film, positioned around the part thus the complete inspected area can be evaluated in one single panoramic image.
X-ray film is still used as the detector because the flexible material allows it to bend over 360deg.
Another reason for using X-ray film is the extremely high contrast resolution, which allows even the smallest details to be shown precisely.
Finally, the individual images meet the high demands for documentation.
All critical gear parts and their welds are checked 100% for rod fusion, air inclusions, cracks and other material faults.
On that basis it is possible to decide whether the part is to be rejected or repaired.
"Presently, there are no alternatives to X-ray inspection", according to Jean-Marc Beninca, responsible for the NDT section at Eurocopter.
"For the future, we are considering whether we can replace X-ray film with a digital image detector in order to save space for archiving.
At the moment, we are still using the old procedure, because it guarantees extremely good image quality." * Helicopter manufacturer Eurocopter, is one of the world's three leading suppliers in the aerospace sector.
The company was established in 1992 on the basis of a merger between Aerospatiale-Matra (France) and DaimlerChrysler Aerospace (Germany) and is now a 100% EADS affiliate.
With more than 1100 employees at 16 international locations, the company earned a consolidated turnover of 2.61 billion Euro in 2003 < 30% of the world market.
More than 9,000 Eurocopters are presently in use in 134 countries.
The line of products includes civil as well as military aerospace engineering and ranges from light-weight single engine helicopters to medium-heavy transport helicopters.
* Viscom develop and manufactured high-speed, high-precision industrial vision systems.
Its world headquarters are based in Hanover, Germany, with facilities and representatives worldwide.
Under the broad banner term "Automated Optical and X-Ray Inspection (AOI and AXI)", Viscom is involved in an extremely wide range of applications and markets, from customised systems, PCB Inspection Systems to X-ray and combined AOI/AXI Inspection systems.
* Inseto, suppliers of equipment and materials for industry, are the UK and Irish technical representatives for Viscoms X-ray equipment.
The quality requirements in the field of aerospace engineering are extremely high.
Material weakness or faults can have fatal consequences for the final consumers and economic consequences for the manufacturers.
For this reason, entirely reliable material inspection is required, which allows non-destructive testing on the one hand, whilst simultaneously providing complete documentation of the test results.
Usually, a 100% test is required when each individual part is inspected.
An inspection procedure, which fulfils these high requirements while also reliably recognising concealed faults, is X-ray inspection.
• Inseto (UK): contact details and other news
• Email this article to a colleague
• Register for the free Manufacturingtalk email newsletter
• Manufacturingtalk Home Page
Search the Pro-Talk network of sites
