Product category:
CMMs (co-ordinate measuring machines) and software
News Release from: LK | Subject: LY90S horizontal-arm, CMMs
Edited by the Manufacturingtalk Editorial
Team on 29 October 2003
Twin CMM system checks sports car bodies
To check the quality of the Aston Martin DB9 GT sports car structure, a new metrology facility has been established at the company's recently opened factory in Gaydon, Warwickshire.
The body of the Aston Martin DB9 GT sports car, launched on 9th September 2003 at the Frankfurt Motor Show, has an aluminium-bonded frame that is 25 per cent lighter than that of the DB7 which is being replaced, yet has double the torsional rigidity To check the quality of this structure before the car is hand built around it, a new metrology facility has been established at the company's recently opened factory in Gaydon, Warwickshire
This article was originally published on Manufacturingtalk on 14 Jul 2000 at 8.00am (UK)
Related stories
Measuring software cuts Jaguar's time to market
The ability to program inspection machines well in advance of the prototype stage is helping Jaguar to shorten the lead time between drawing board and forecourt.
Mitutoyo CMM programming time halved by software
At Luton-based Huntleigh Healthcare, the time taken to program a seven year old Mitutoyo co-ordinate measuring machine (CMM) has been halved using CAMIO software
Central to its operation is a pair of LK computer-controlled LY90S horizontal-arm, co-ordinate measuring machines (CMMs) for inspecting external features on both sides of the vehicle simultaneously in fully automatic, mirror-image cycles that take around two hours.
Together the CMMs provide a measuring volume of 6000 x 3000 x 2500mm, sufficient to contain the whole vehicle, which is held in 'car line' by bespoke fixturing during measurement.
Results are accurate to better than 10 microns over the length of the car.
Further reading
CMM software applicable to LK and other makes
LK, has introduced a new, advanced suite of programming software for use with its own and other manufacturers' co-ordinate measuring machines.
Complex aerospace CMM programming uses CAD data
Subcontractor Castillion says it would not really be able to handle some of the work it does now without LK CAMIO, a CAD-to-CMM interface which allows solid models to be imported and used
CMM upgrade allows import of solid models
Derbyshire-based co-ordinate measuring machine (CMM) manufacturer, LK, has upgraded the Zeiss CMM at the Heraeus QuartzTech factory, which produces silica quartz ovenware for semiconductor makers.
A further key feature of the installation is LK's CAMIO interface software, which enables the data within Aston Martin's CAD files to be downloaded to the CMM environment and used to create measuring programs directly from the models.
When the DB9 enters full production early next year, every day a body fitted with doors, bonnet and boot lid, a so-called 'body complete', will be taken out of production at random and checked for each of four car variants (left- and right-hand drive versions of the coupe and the convertible).
In addition, the LK LY90S cell will potentially have to measure a wide range of items, from a fully assembled car to a single component.
The purpose will be to investigate build issues, verify supplier measurements and make data available to the engineering and design departments for finessing and continuous product improvement.
A further duty will be to support the development of future Aston Martin car models through their prototype stages.
In addition to inspecting the DB9 body during its development, the LK LY90S cell was used routinely to measure a wide variety of parts from simple brackets to a complete transmission, as well as to check fixtures used on the framing machine in which the car body is bonded.
To achieve this breadth of measuring capability, the flush-floor steel bedplate has been drilled at 200 mm centres to accept flexible fixturing, allowing components of any size to be clamped accurately for inspection.
To ease the workload on the cell when measuring smaller components, an additional LK bridge CMM, a G90-C with a measuring envelope of 800 x 700 x 600 mm, has been installed in the same temperature-controlled room.
Programs are interchangeable between the two machines.
Said Simon Skinner, projects engineer for the manufacturing engineering department at Gaydon, "The LK LY90S cell supported the DB9's prototype phase right from the start, helping to reduce the lead time to develop the car.
This was possible because LK's CAMIO interface software, uniquely at the time, was immediately able to read the I-DEAS CAD files from our design department, enabling inspection programs to be written in advance of prototypes becoming available." So successful was this process that senior dimensional technician, Richard Winspear, had prepared all the programs for inspecting the DB9 'body complete' before the LK CMMs had even been installed in January this year.
It was then a simple matter to prove out each program on the machine and make minor adjustments.
Said Mr Winspear, "I programmed each element of the car body separately using an off-line LK CAMIO terminal, so we ended up with a suite of modules that can be run in any sequence using LK's graphics-based Launchpad software.
The automatic cycle can be over-ridden as required to enable manual inspection of additional features.
"This approach is helpful during the development phase while we need to check individual elements.
When inspection starts in support of production, the modules can be stitched together into one seamless, fully automatic sequence for measuring 700 points over the entire body." When production starts, Aston Martin will take advantage of LK's statistical process control software to analyse manufacturing trends and will be able to embed SPC charts in graphical reports generated automatically by a further software module.
The reporting system has been adapted from that used by sister Ford Premier Automotive Group companies, Land Rover and Jaguar, which use LK CMMs to support their metrology requirements.
Concluded Mr Skinner, "Our investment in the new metrology facility at Gaydon sprang from a projected doubling of annual production next year.
Moreover, an additional model to be introduced in 2005 will double production output again.
"Our previous inspection techniques using portable measurement arms, verniers and gap gauges would be too slow to support these larger volumes, which is why we have moved over to automated inspection using LK CMMs.
"In any case, the immediate availability of measured results in electronic form and the ability to tie them back to the CAD model allows us much wider scope in integrating the quality function with other departments and brings us in line with best practice within the volume car manufacturing sector.".
• LK: contact details and other news
• Email this article to a colleague
• Register for the free Manufacturingtalk email newsletter
• Manufacturingtalk Home Page
