Product category:
System integration services
News Release from: Modular Automation International | Subject: Automotive pedal sensor assembly system
Edited by the Manufacturingtalk Editorial
Team on 27 August 2002
Safety-critical accelerator pedal sensor
assembled
A system assembles accurately the 8 components of a safety-critical throttle position sensor, and checks the component's function, all with a cycle time of just 9 seconds.
in 9 sec Modular Automation has designed an assembly system for Wabash Technologies that can assemble accurately the 8 components of a safety-critical throttle position sensor, and check the component's function, all with a cycle time of just 9 seconds The sensor is for a leading Tier 1 pedal manufacturer whose generic throttle pedal design positions it well meet the requirements of many major OEM's
This article was originally published on Manufacturingtalk on 28 Jan 2002 at 8.00am (UK)
Related stories
Negari system supports lean manufacturing
Modular Automation from Birmingham, has designed and built a new semi-automatic assembly system for Delphi Diesel of Sudbury that complies with the company's Lean Manufacture principles.
Vision system speeds up automotive glazing cell
A glazing cell, using a vision system, has reduced the cycle time to around 33 seconds - down from 3 minutes required with a fixed-jig, manual system used previously.
The sensor provides electronic throttle control that is more accurate and more reliable than cables.
Electronic control is also maintenance free.
The process is essentially automatic but requires two operators to load critical components.
Further reading
Automated insert system keeps work at home
A new plastic insert loading system for a moulding press has improved efficiency sufficiently to allow the user to keep medical equipment production in the UK.
Assembly system switches LH to RH automatically
A new system assembles spring bolts for a new range of Yale locks that can be switched easily from left to right-handed without dismantling, as required before.
System to repair vehicle windscreens
One of Britain's top product design agencies, PDD has selected Modular Automation International to design and build production equipment for a new windscreen repair system.
Each operation is checked to make sure that it took place correctly; any incorrect assemblies are flagged on the pallet and pass through without further work.
Laser trimming calibrates the resistance of the unit and an electronic test also ensures that each completed assembly works correctly.
The operator first loads a housing and rotor onto a flagged pallet.
The first automatic station then loads the substrate, ensures that it is laid flat and heat stakes it into position.
The system checks only that the substrate is present, not that it performs correctly.
Electronic testing is carried out later in the process.
This maintains a practical outlook on testing to ensure that every component is tested adequately yet avoid duplication.
Further operations load the spring, rotor and cover, which is heat staked into position to complete the assembly.
There are, however, three operations that are particularly technically demanding: wire bonding, spring contact assembly, and laser trimming.
The wire bonding station uses a proprietary wire bonder to weld 9 hair-thin wire contacts into position to link the substrate with the electrical contacts moulded into the sensor body.
This is a very delicate operation that must be completed perfectly for the sensor to operate correctly.
The spring contact assembly positions three twin-spoked contacts and heat stakes them to secure.
The contacts are only 4mm wide and only 75mm thick and must be secured without deformation.
The system uses a force guage to measure the pressure exerted by every spoke of the contact on the substrate track - too little force would cause a bad connection, to much would wear the track and result in premature failure of the component.
Laser trimming of the substrate track calibrates the final assembly to ensure it has the correct resistance at a zero mechanical position.
The system checks the resistance before and after the trimming process.
Again this is a critical operation that ensures the correct operation of the sensor.
In designing the assembly system Modular Automation has combined its modular philosophy and bespoke creativity into a compact, reliable system that produces zero defect components for this safety critical application.
Modular Automation has vast experience at developing innovative assembly systems using a modular approach and trusted technology.
By approaching its business in this practical way it ensures that its systems are realistically priced, effective and utterly reliable.
• Modular Automation International: contact details and other news
• Email this article to a colleague
• Register for the free Manufacturingtalk email newsletter
• Manufacturingtalk Home Page
Search the Pro-Talk network of sites
