Product category:
Conveyor systems (production and general purpose)
News Release from: Montech | Subject: Mini-conveyors
Edited by the Manufacturingtalk Editorial
Team on 02 November 2000
The compact and more efficient mini
conveyors
Montech is launching a series of new Mini-conveyors which complement its existing Low-profile models and use a 24V brushless DC motor, rather than the more traditional AC variety
Montech is launching a series of new Mini-conveyors to complement the existing Low-profile models The new range uses a 24V brushless DC motor, rather than the more traditional AC variety
This article was originally published on Manufacturingtalk on 20 Jun 2001 at 8.00am (UK)
Related stories
Single belt used for lower cost pallet transfer
The inherent simplicity of the Montech single belt system, is not only cheaper to purchase than a comparable twin-belt system, but it is also much less costly to adapt, modify or expand.
Slide units simpler for pick-and-place
If all of these add-on costs are taken into account, a combination slide and actuator is likely to work out much cheaperthan designing a unit using individual components, says Montech.
As well as being more compact, quieter and energy-efficient, the Mini-conveyors also benefit from a facility for controlling speed, direction, acceleration and deceleration.
Moreover, compared with an AC motor, the DC unit provides a virtually constant torque-speed characteristic.
There are certainly similarities between the new Mini-conveyor and Montech's existing Low-profile conveyors, such as the chassis extrusions, end roller housings, wide choice of belt materials, and accessories - including stands, side guides and sensor brackets.
Further reading
Motor assembly cell based around indexing table
When Schunk decided to automate the assembly of the brush holders for its electric motors, the company wanted to build itself a machine quickly.
Pallet transfer without the pain
Montech has come up with a solution that mitigates the noise problems often associated with pallet transfer systems, using clever design including elastomeric shock absorbers
But the Mini-conveyor is available in a narrower conveyor width (45mm) in addition to the previous four sizes between 60 and 140mm, and there is now an option to mount the motor on a swinging arm at either end of the conveyor, thereby giving clearance that allows flighted belts to be used for the first time.
Although the motor is rated at 24V DC, it is capable of operating from any DC supply within the range 14-28V, and the control electronics can easily cope with unsmoothed currents or voltages.
Long cables from the power supply to the conveyor do not cause problems either.
Each conveyor is equipped with several means by which the belt can be controlled.
The first is a simple on/off switch on the keypad, with the speed set via the same keypad.
One alternative is to use a 24V signal, perhaps from a PLC, to switch the conveyor on or off remotely; however, if a PLC is used, there is the option to use two signals, allowing the conveyor to be run automatically in either direction.
Speed, acceleration and deceleration can all be pre-selected and locked, ensuring that operators cannot subsequently tamper with these settings.
Note also that each conveyor is fitted with an electrically-operated brake as standard.
Despite its compact size, the Mini-conveyor can carry a very respectable 22kg.
The maximum length is 12m for the version with the underslung motor, or 5m if the end-mounted motor is chosen.
Two speed ranges are offered: 0.4 to 7.3m/min, or 1.2 to 21m/min, and the digital display on the control panel indicates the actual speed.
The ramp-up time can be programmed to be any time from 0.5s to 5s.
Lastly, don't forget that Montech guarantees the conveyors for two years, even if they are run continuously at full load.
And because the motors are brushless DC types, there is no need to change the brushes every 5000 hours, which would be the case for a typical brushed DC motor.
• Montech: contact details and other news
• Email this article to a colleague
• Register for the free Manufacturingtalk email newsletter
• Manufacturingtalk Home Page
Search the Pro-Talk network of sites
