Product category:
Robots and robotic systems
News Release from: Motoman Robotics (UK) | Subject: Articulated arm robots
Edited by the Manufacturingtalk Editorial
Team on 12 October 2004
Slimmer robots get better access
A range of 6-axis, all-electric, articulated-arm robots has been introduced by Motoman.
A range of 6-axis, all-electric, articulated-arm robots has been introduced by Motoman to replace its mainstream UP-series, compared with which the new models offer significant improvements Designated HP-series, the latest robots are slimmer to allow better access, yet offer greater all-round reach as well as improved positional accuracy and a slightly higher payload for any given model
This article was originally published on Manufacturingtalk on 14 Jul 2000 at 8.00am (UK)
Related stories
Ford uses Motoman robots for sealant application
As an alternative to fitting conventional gaskets to seal the mating faces of vehicle engines, Ford finds that a quicker and more economical method is to lay down a bead of sealant by robot.
Articulated-arm robots offer larger envelope
The SK Series of articulated-arm robots from Motoman has been replaced by a new range, designated UP Series.
They are also lighter, leading to a 15 per cent reduction in power consumption, and are more reliable, with a mean time before failure of 250,000 hours.
Further benefits are a reduction in operating noise to below 75dB, and improved protection against ingress of dirt, dust and fluids from IP54 to IP67, which applies to the whole robot, not just the wrist.
Care has been taken in the design to simplify maintenance, allowing the robot to return to production faster.
Further reading
Robots weld X400 seat frames
Two robotic welding cells have been supplied by Motoman to the Birmingham factory of Lander Automotive to automate the manufacture of complex assemblies for the new Jaguar X400 saloon car.
Robots polish off catrering ware much quicker
One of Europe's leading stainless steel catering and sanitary ware equipment manufacturers, W and G Sissons, has embarked on a far-reaching programme to automate polishing at its Chesterfield factory.
Motoman appoints systems integrator in Essex
Specialist motion control system builder, Micromech, based in Braintree, Essex, has been appointed a systems integrator by articulated-arm robot supplier, Motoman Robotics (UK), Banbury.
For example, rotary encoders were previously built in, whereas now they are removable for speedy replacement.
There is also a cost saving, as the whole motor/encoder assembly does not need to be changed.
There are four models in the range HP6, HP20, HP50 and HP165 the suffix number representing the nominal payload in kilograms.
At the same time, Motoman has launched a new, patented robot controller, designated NX100.
Replacing the XRC, the control is now Windows-based and has a colour rather than a mono teach pendant display.
However, its big advantage is that it can control 36 axes simultaneously, an increase of nine.
It is thus the first controller to be able to synchronise the movements of four robots and work handling equipment simultaneously, in the same way as Motoman's previous controllers were the first to handle two and then three robots plus peripherals.
Other user advantages of the NX100 are many.
There is more flexibility in the way the external axes are configured, now in groups of three so that they may be switched off for repair while the other robots continue to operate.
The controller has a program capacity of 60,000 steps and 10,000 instructions, up from 5000 and 3000 respectively.
Standard I/O is the same at 40 in and 40 out, but there is the new option of increasing these to 1,024, four times more than before.
Maximum analogue I/O is increased from 12 to 40.
An Ethernet card is built in as standard for better communication with the robots and peripherals.
As with the HP robots, the new controller has been designed with ease of servicing in mind.
Average downtime for simple repairs is five minutes, compared with 40 minutes before.
A further innovation is the ability to specify IP54 protection instead of the standard IP33.
Introduction of the HP-series follows Motoman's launch last year of application-specific robots, the ES165 for spot welding and the EA1900 for arc welding.
The rationale behind their introduction is to integrate the services that are normally added when a generic robot like the HP is configured for the respective applications.
This carries the risk of trailing cables and hoses becoming either snagged or fatigued through repetitive flexing.
An additional advantage is that the robots can operate more closely to the workpiece, and access to difficult areas is improved.
• Motoman Robotics (UK): contact details and other news
• Email this article to a colleague
• Register for the free Manufacturingtalk email newsletter
• Manufacturingtalk Home Page
Search the Pro-Talk network of sites
