Product category:
Horizontal machining centres (HMC)
News Release from: NCMT | Subject: Makino A71 and A81 horizontal machining centres
Edited by the Manufacturingtalk Editorial
Team on 16 September 2003
'Entry level' HMC range expanded
Following the earlier introduction of its lower priced 'entry-level'A51 HMC, Makino is now producing two larger machines based on the same design.
Following the earlier introduction by Makino of the A51 horizontal machining centre (HMC), an entry-level model priced to attract smaller companies, mould makers, subcontractors and others that may be on a limited budget, the Japanese manufacturer has announced two larger machines based on the same design Designated A71 and A81, they cost significantly less than the manufacturer's mainstream products of equivalent capacity
This article was originally published on Manufacturingtalk on 26 Jun 2003 at 8.00am (UK)
Related stories
Entry-level HMCs grow in size
Following the introduction last year of an entry-level HMC priced to attract SMEs and mould-makers, two largter models, based on the same design, are now available.
HUD chassis lead-time cut by more than one half
The lead time for machining a head-up display (HUD) chassis has been reduced from 53 days to 20 by Thales Optics after installing an Okuma MA50 half-metre-cube, horizontal machining centre.
The latter model will be on show for the first time in Europe at EMO.
Sole UK agent, NCMT, points out that the price differential has not been achieved at the expense of quality and there is little compromise on functionality.
Steps taken by Makino to engineer out cost include a 40 per cent reduction in the number of machine components, which has the additional advantage of enhanced operational reliability.
Further reading
Getting gear blanks round and parallel
For successful gear manufacture, roundness and parallelism have to be very accurate, which is why motor sport gearbox maker, XTRAC, acquired Okuma CNC lathes for gear blank machining.
Rotary coolant adapter avoids bearing wear
A rotary coolant adapter uses split construction to separate the bearing housing from the coolant collar to increase reliability over extended service life.
New low-cost lathe from Okuma
Okuma has introduced a 2-axis CNC turning machine, called Soarer L270E, which is the first of a new range from the Japanese manufacturer built to in-house standards under contract in Taiwan.
The half metre cube capacity and 400mm2 pallet of the A51 has been extended on the aA81 to provide a working envelope of 900 x 800 x 900mm and a pallet size of 630mm2.
What the customer receives is a compact machine with a generous standard specification, including through-spindle coolant, chip conveyor, 40 (60 or 132) station magazine for 50 taper tools (or HSK-A100), pallet changer and a one degree indexing table.
Use of a three-point suspension system allows the machine to be installed and levelled without special foundations, provided that the shop floor is sound.
It is easy to incorporate these lower cost models into existing lines containing full-specification Makino HMCs.
Such an arrangement would allow economical expansion of an FMS using A81(s) to complete simpler tasks while the existing machine(s) carry out cycles that demand faster axis motions as well as more spindle speed and power.
Nevertheless, the new arrival is fast and highly productive in its own right and will accept a 1.2 tonne workpiece on the pallet.
Maximum spindle speed of 10,000 rpm is delivered in 2.4 seconds by an integral 22/15kW motor, whose acceleration to half that speed is an impressive 0.8 second.
Rapid traverse is also fast at 60m/min in all axes.
Contributing further to minimum non-cutting times are automatic tool change in 1.7 seconds tool-to tool, 3.5 seconds chip-to-chip, and pallet indexing in under 2 seconds for 90 degree rotation with a 500kg load.
Very high precision metalcutting is claimed by Makino, as befits a machine with an installed weight of 21 tonnes.
Accuracy and repeatability are +/-0.004mm and +/-0.002mm with rotary encoder feedback, or 25 per cent better if linear scales are specified.
Measures taken by Makino to achieve this level of accuracy includes controlling the cooling oil to the same temperature as the bed and recirculating it through hollow ballscrews in all axes.
Makino's own GI (Geometric Intelligence) control allows maximum advantage to be taken of the high speeds and feeds when rough milling, drilling and tapping.
Where higher accuracy is more important than top productivity, three further control modes may be selected. Request a free brochure from NCMT ...
• NCMT: contact details and other news
• Email this article to a colleague
• Register for the free Manufacturingtalk email newsletter
• Manufacturingtalk Home Page
Search the Pro-Talk network of sites
