Product category:
Measurement systems
News Release from: Orlin Technologies | Subject: Screw thread inspection systems
Edited by the Manufacturingtalk Editorial
Team on 10 January 2006
Threads inspection is automated
Ever stricter specifications for the acceptance of automotive parts have increased the pressure for 100% quality inspection of all manufacturing processes- including screw threads.
Ever stricter specifications for the acceptance of automotive parts have increased the pressure for 100% quality inspection of all manufacturing processes over the last few years Thread inspection is no exception
This article was originally published on Manufacturingtalk on 1 Nov 2005 at 8.00am (UK)
Related stories
Actuator solves connector assembly problem
The motion and force profile of a moving coil actuator can be accurately controlled over the entire stroke of the device allowing it to pick up a pin and press it into a connector housing.
Moving coil actuator speeds up bowl feeder
Moving coil actuators have allowed an electronics manufacturer to increase production speed by feeding more than 15 parts per second from a bowl feeder into its process.
Until recently the common practice has been the use of Eddy Current probes, lasers, proximity sensors or a vision system.
These systems were successful to some degree in the past but today's quality-conscious end customers need to know more than just the presence of a thread.
A major automotive manufacturer has recently chosen an automated thread checking solution developed by SMAC for 100% quality inspection of tapped threads in a cylinder head.
Further reading
Actuators offer high speed, accelerations, acuracy
Low moving mass and low friction, combined with direct drive mean that moving coil actuators are unmatched for speed, acceleration, accuracy and repeatability in 'pick and place' applications.
Automated quality control for airbag component
An automotive Tier 1 supplier approached SMAC to provide an automated quality control solution for a safety-critical airbag component.
Test rig takes on any gearbox
Westland Transmissions in Yeovil has installed a new flexible transmissions test rig (FTTR), as part of a GBP9 million investment that is being used to test helicopters.
The manufacturer's requirement included checking for: * Thread depth.
* Number of threads.
* Faults such as crossed thread, no thread.
* Oversize/undersized thread indicating worn or damaged tap.
Other requirements were: * High throughput.
* Objective measurement data output for each part for quality control.
* Reliability - 24/7 operation.
* Cost effective solution.
The traditional method for checking threads would have been by hand with a screw plug gauge.
This process is labour intensive, subject to human error and relies on a skilled workforce.
The SMAC solution takes this well proven manual technique and automates it allowing it to be integrated into a modern production environment.
A conventional thread gauge is mounted on a linear/rotary actuator (in this case an LAR55-100-75FS).
All of SMAC's LAR series actuators have high resolution linear and rotary encoders for precise position measurement of angle and distance.
This data is monitored by the controller and compared to pass/fail parameters to identify and reject faulty parts.
It can also be interpreted and fed back to a database for a complete Quality Control history.
To carry out the checking procedure, SMAC's unique softland routine is employed to find the part, landing with a controlled, low force so as not to damage the gauge.
While maintaining a low contact force, the actuator then rotates anticlockwise until the thread gauge drops into the thread (indicated by a sharp change in linear position).
It then rotates clockwise at a pre-determined torque, driving the gauge into the thread (an over-torque situation indicates a fault such as crossed thread, insufficient thread depth or excessive debris).
Other checks that can be carried out include measuring linear motion during one rotation of the rotary axis confirming the pitch of the thread and a push-pull test with the rotary axis held stationary giving the play in the thread.
When combined with SMAC's controllers, the actuator is fully programmable in position, velocity, acceleration and force, and therefore can carry out a comprehensive, qualitative check of a screw thread in just a few seconds.
Part changeover is achieved simply and easily by selecting a different program (either memory-resident or downloaded via RS232) and if necessary, changing the thread gauge.
• Orlin Technologies: contact details and other news
• Email this article to a colleague
• Register for the free Manufacturingtalk email newsletter
• Manufacturingtalk Home Page
