Product category:
Monitoring and sensor equipment and systems
News Release from: RDP Electronics | Subject: ACT6000 300mm LVDT
Edited by the Manufacturingtalk Editorial
Team on 14 November 2002
Transducer sorts out test rig for
tail-lift firm
The originator of the vehicle-mounted tail lift turned to the internet and then to RDP Electronics for displacement transducers, load cells, amplifiers and displays for a test rig
As the originator of the vehicle-mounted tail lift, and the UK's market leader for over 40 years, Ratcliff prides itself on its innovation and build quality Whilst the company's engineers design their lifts using finite-element stress analysis, they need to verify statutory overload capability by carrying out physical tests
This article was originally published on Manufacturingtalk on 3 Jul 2002 at 8.00am (UK)
Related stories
Brochure is invaluable to systems designers
RDP Electronics has published a new 6-page short-form colour brochure describing its comprehensive range of transducers and instrumentation.
Sheets describe transducers and sensors
Three new technical data sheets describe the a series of draw-wire displacement transducers, low pressure transducers, and proximity and linear displacement sensors.
Ratcliff establish the yield strength of each model, and retain the records in the lift's CE Technical File.
The traditional method of determining the ultimate strength of a lift has been to apply calibrated weights huge steel blocks - stacked one by one on the tail lift's platform until the yield point was reached.
But Alan Barsby, Engineering Director at Ratcliff Tail Lifts, was not satisfied.
Further reading
Torque transducer is small and accurate
With an impressive overall accuracy of 0.25% full-scale, a torque transducer is designed to meet demands for high accuracy, small size with mounting options.
Sensor signal conditioner displays all the answers
A compact control hub for stand-alone measurement systems combines an 'all-in-one' conditioning unit for a wide variety of LVDTs, and most strain gauge sensors, with local data display and network.
Non-contact system measures rotation accurately
Patented capacitive technique provides a high accuracy, non-contact, no friction solution to measuring rotary displacements of shafts.
Not only was this method a time-consuming and often destructive procedure, it was, particularly with high payload lifts, potentially dangerous.
After the test, there was no clear indication of the primary failure mechanism.
Again, comparative tests of central, distributed and off-set loading were impractical and the method was not sophisticated enough for Ratcliff's new generation of lightweight all-aluminium tail lifts.
Ratcliff devised a test rig made from a rigid steel cage incorporating a hydraulic ram capable of exerting up to 125,000 N of load at any point on a platform through a pressure pad, matched to the footprint of the intended load.
The equipment will handle the full range of the company's products, from the smallest passenger lift to the biggest column and cantilever models.
One phrase - 'displacement transducers' - typed into an internet search engine brought Alan to the virtual front door of RDP Electronics.
As he explained, "I looked through the website and found, from one company, everything I needed: displacement transducers, load cells, amplifiers and displays.
"The most important requirement was the ability to plot a load/displacement curve in real time.
"In that way we could view the approaching yield point without destroying the test sample.
"So I made a call and spoke to Fred." RDP's Fred Thorneycroft worked with the Southern Area Sales Engineer, Ken Irvine, on a solution.
"Ken visited us, discussed the problem and the solution was relatively simple." explained Alan.
An ACT6000 300mm LVDT and E725 AC conditioner/indicator were chosen to measure the deflection caused by the increasing load, and a 53-20,000lb load cell in an articulated knuckle joint with another E725 DC (calibrated to read in tonnes) was fitted to the base of the ram to measure the load.
He continued, "The two E725s were connected to a PC via the RS485/RS232 option to provide a stress/strain plot and Ken then set up RDP's Excel-based spreadsheet and chart software for us.
"We could not have asked for a better service: the test rig works exceedingly well, and we are delighted with the performance.
"We are able to explore the ultimate strength limits of prototype lifts without causing damage.
"Currently, we are using the equipment to establish the yield point of a heavy-duty platform with a concentrated load of more than nine tonnes.
"This would have been out of the question using dead-weight methods." . Request a free brochure from RDP Electronics ...
(This was Manufacturingtalk's Top Story on 13 November 2002).
• RDP Electronics: contact details and other news
• Email this article to a colleague
• Register for the free Manufacturingtalk email newsletter
• Manufacturingtalk Home Page
Search the Pro-Talk network of sites
