Aqueous cleaning cuts sheet metal finishing costs

Propak has achieved cost reductions in component cleaning, degreasing and painting after replacing a trichloroethylene (trike) dip tank with a Turbex aqueous cleaning and phosphating machine.

Based on 24-hour operation for five days a week plus weekend working, the company previously used the trike Safetainer system, each costing GBP625, once every month or two depending on workload.

In addition, 500 litres of two-pack etch prime per month were used to prepare sheet metal for painting by wet or electrostatic powder coating.

With the Turbex AC-2.5-3 water-based cleaning machine, the cost of trike is eliminated.

After aqueous cleaning, the machine applies an iron phosphate coat to all parts that will be painted, which accounts for around 70 per cent of throughput.

Only around 25 litres of etch prime is now used, mainly for priming stainless steel, which cannot be iron-phosphated.

Consumables for the aqueous machine involve an outlay of GBP120 per month for the detergent and phosphate, both of which are harmless to the environment, plus GBP400 every three months for an in-line water filter.

This option allows water to be recycled and reused for inter-stage rinses, rather than immediately being lost down the drain.

Propak said that after the price of the aqueous consumables have been taken into account, savings in trike and etch prime result in an annual reduction in cleaning and priming costs of up to GBP12,000.

The amount of heat used is equivalent in the solvent- and water-based processes, so this was a neutral factor in the calculations.

Financial benefits extend to the purchase of the Turbex machine itself.

The solvent emissions directive dictated a change from the existing open-top trike tank, which will shortly be removed from Propak's factory.

It could have been modified at a cost of GBP35,000, or a new, enclosed solvent tank purchased for more than GBP80,000.

Installed in 2007, the Turbex AC-2.5-3 was less costly and accommodates in its 2.3m x 2.3m x 0.9m wash chamber all of the component sizes that the solvent tank was able to, as well as larger sizes.

It was Propak's choice to have water filtration and recycling fitted as well as deionisation of the final rinse water, which results in a further financial saving through reduced water usage.

As far as the local water board is concerned, it would have been happy for the water and non-hazardous chemicals to go straight into the drain at the correct pH level, as it would have helped to clean the sewerage system.

According to Propak, the degreasing efficiency of the aqueous, spray wash cleaning machine is equivalent to that of trike and overall lead time to prepare components for painting is similar with both systems.

With the Turbex process, work is ready to paint, as it is already pretreated with iron phosphate.

A typical cycle in the front-loading AC-2.5-3 takes around 20 minutes, including 60-75C detergent wash, 50-55C phosphating, final 60-75C water spray rinse and steam extraction.

Door lift is automatic when the cycle ends and minimal effort is needed to move the table in and out of the work area to load and unload components.

A benefit of the multi-stage Turbex machine is the precision with which components can be cleaned, as all parameters are variable from the control panel.

Propak has four wash programmes preset for short and long cycles, according to the amount and types of soils on the components, and the option of using two phosphating cycles to suit the adhesive properties of the metal being processed.

Material gauge can be anything from 1mm sheet to 15mm plate.

Components frequently find their way into military vehicles and other defence-related equipment, medical devices such as X-ray enclosures and across industry generally, both in the UK and overseas.

Having decided to go down the aqueous cleaning route, Propak looked at a number of alternative machines.

Turbex was chosen due to the quality of its machine's stainless-steel construction and the accessibility for maintenance.

For example, heaters and pumps may be changed quickly, without having to drain down the system.

The company also reported that it has received good service back-up from Turbex.

Back to top