Product category:
Plastics and Rubber Moulding Subcontracting Services
News Release from: SPECIAL REPORT by the Editor | Subject: Subcontract plastics moulding
Edited by the Manufacturingtalk Editorial
Team on 29 August 2007
Multi-component injection moulding
processes
A limitation to achieving the aspirations of designers has been the ability to process multiple parts or materials into a single component when moulding plastic assemblies, writes Jon Hobden.
The advancement of plastics and rubber mouldings technology over the past forty years has been steady and impressive However, a limitation to achieving the aspirations of designers, in industries such as medical, automotive and aerospace in particular, has been the ability to process multiple parts or materials into a single component, without the need to bond or join the parts in separate assembly processes
This article was originally published on Manufacturingtalk on 1 Aug 2007 at 8.00am (UK)
Related stories
Subcontractor production software comes of age
Over the past 40 years, manufacturing software has blossomed from simple machine control to encompass estimating and quoting, cost control, tooling management and more, reports QA editor, Jon Hobden.
Conduit systems safer when the rules are followed
When electrical systems and even mechanical systems are designed and built, the specification of adequate or suitable conduit and conduit components is often ignored, writes Jon Hobden.
Multi-component injection moulding is not new but the difficulties involved make it expensive and inconsistent in many cases.
Processes such as encapsulation of a first-process mould by a second, often by mould indexing, are common.
But the ability to insert-mould or two-shot mould to exacting accuracies and repeatability requirements are still the domain of specialist mould shops.
Further reading
Coordinate measurement relies on good software
Jon Hobden looks at the development of Coordinate Measuring Machines and the importance of finding the right CMM software for a given application.
Very narrow aisle trucks bring productivity
The increasing adoption of very narrow aisles in warehousing and storage has lead to a number of design challenges for lift truck manufacturers and a resurgence in narrow-aisle innovation.
The role of Six Sigma in production and service
Six Sigma uses a mixture of statistical tools and other techniques to first, identify areas that can be improved, then control and improve processes, writes Jon Hobden.
One such is British technical moulder A K Industries (AKI) of Hereford, providing design and manufacturing offerings using multi-component moulding.
A particle analyser manufactured by Malvern Instruments utilises a disposable capillary unit or cell, designed to measure as small as 6nm particles.
The cell has gold plated electrodes moulded-in to the clear, polycarbonate component, with a AKI-designed carrier loading the electrodes with very high precision.
Two moulded halves are welded ultrasonically as part of the process to partly encapsulate the terminals.
Every piece is tested before shipping.
The cell is required to be optically clear to prevent light scattering in the plastic, watertight under pressure and accurate to accept the correct amount of liquid in the measuring chamber.
A complete manufacturing cell built by AKI moulds, inserts, welds ultrasonically, inspects inline and packs after testing.
AKI is also able to manufacture complex mouldings using two different polymers in one cycle on the same machine.
Where compatible materials are specified, fusing of the two parts takes place when the second part is moulded-in to the first.
Mechanical bonding is also available for incompatible materials, where the two cannot be chemically bonded or where movement/articulation are required by the design.
The two-shot injection moulding process is the ability to produce complex mouldings from two different polymers at the same time during one machine cycle.
Separate but compatible materials or colours are very strongly fused together (chemically bonded at the molecular level) through the forming process when the second material is injected into the mould.
Alternatively, incompatible materials can be mechanically connected by two-shot moulding without fusing, in order to meet specific product design and assembly needs such as articulation or movement.
A trace detector made by AKI for 3M Health Care, that measures ATP for hygiene applications, involves a two shot process to produce a cuvette which is tapered and possesses a seal of TPE that is moulded into the component.
A sixteen-cavity tool is divided into four, each segment having a precision water cooling facility to maintain the integrity of the completed unit.
Two different polymers are also used in a muscle toning system the company makes for Dezac Group, the toning pad bonded into the back of an oval hinged surround.
With a complete concept-to-delivery service, combined with the expertise and experience to push boundaries, AKI has brought multi component moulding into the mainstream with precise and consistent results possible.
• SPECIAL REPORT by the Editor: contact details and other news
• Email this article to a colleague
• Register for the free Manufacturingtalk email newsletter
• Manufacturingtalk Home Page
Search the Pro-Talk network of sites
