Product category:
Drives, motors and power transmission, couplings, clutches
News Release from: ZF Great Britain | Subject: Hysteresis tension control systems
Edited by the Manufacturingtalk Editorial
Team on 27 December 2005
Hysteresis tension control raises press
output
Hysteresis tension control systems reduce downtime and increase production of a high precision pressing machine at the UK's largest rubberised printing sheet manufacturer.
ZF Hysteresis Brakes and Clutches have provided Day International (UK) , the UK's largest rubberised printing sheet manufacturer, with over 12 months of problem free operation in a high precision pressing machine Following the successful application, two more machines in the process have been upgraded with ZF tension control systems as part of an internal continuous improvement drive, resulting in reduced downtime, minimised waste and standardised spares
This article was originally published on Manufacturingtalk on 10 Dec 2007 at 8.00am (UK)
Related stories
Comprehensive service maintains off-highway plant
An off highway maintenance operation has launched a comprehensive new service covering all its gearbox and transmission products.
Electronic control systems provide diagnostics
An advanced transmissions diagnostic programme solves the problem of unscheduled downtime, allowing for preventative maintenance and, hence, maintenance times to be planned.
Whether meeting the high-speed requirements of newspaper presses or providing the accuracy to flawlessly print banknotes, the rubberised sheets made by Day International have a tough life as they transfer ink to paper in printing presses.
The quality of the sheets and their final performance is dependent on the speed at which they are fed through each production process, with strict parameters to be maintained on tension control systems.
The machines operate around the clock to produce 40,000m2 of sheeting each month and it is imperative to Day that costly downtime is kept to an absolute minimum.
Further reading
Single stage right-angled gearheads
WT Economy single stage right-angled gearheads from ZF, are for OEM designers and maintenance engineers who demand high levels of performance and flexibility from smaller units.
Non-contact hysteresis systems for higher tension
A combination of Brakes and clutches managed by ZF's ERM controllers has proved to have the accuracy and reliability to replace DC drive based tension control systems in presses at Day International.
Web site covers servo gear boxes
Web site covers servo gear boxes, tension control systems and oil coolers for machine builders, engineers and designers in automation and machine tool industries to easily find information.
Over 12 months ago, Willie Allan, Chief engineer at Day International calculated that it was time to replace the tension control system on the first of three main processing machines at their Dundee production facility.
This first major stage involves attaching the rubber to a fabric backing via a highly accurate rolling process.
This complex web application required keeping a consistent tension on the fabric backing as it is fed into the machine, coated with adhesive and attached to the rubber sheeting.
"The company continually looks to improve and develop the way we manufacture our products to provide even greater consistency to our customers and this is an area were we decided we could improve on our existing DC drive based tension control system," comments Allan.
"We then contacted our local drives system supplier JR Power, who recommended that we fit ZF EKU hysteresis clutches to each of the unwind systems and an EBU brake to the onwind assembly.
We had considered a manual clutch system, but had rejected the idea due to risks of contamination from dust particles, a problem conveniently avoided by the magnetic, non-contact operation of the hysteresis units.
They were incredibly easy to fit," continues Allan, "And the set up was quick and simple, as we only had to program the parameters into the PLC and the ZF units provided flawless tension control despite a large difference in tension as the material rolls vary in diameter.
If there is too much tension the sheets become too thin, reducing wear life of the final product and compromising quality.
Too little tension and the sheets become thicker, causing costly problems with the printing presses and irregularities in the print." After 12 months of faultless use and associated increase in output, a similar ZF assembly was fitted to a machine that controls the adhesive curing process of the rubber sheeting.
Again, varying tension would have produced inconsistencies in the properties of the rubber, resulting in weaknesses and inaccuracies in the final print.
This three-way web application includes two inputs of rubber sheet, which are spliced together either side of a paper layer, enabling the materials to be separated once they have been pressed and fed through a curing oven.
Another web made little difference to the time taken to set up the new system as adding an extra EKU unit was simple and straightforward.
Operation was proven to be superior to the old inverter based system in terms of setup, downtime and improved end product.
Grinding the surfaces of the cured rubber sheeting is one of the final operations in the process and yet requires the highest levels of tension control.
The three grinding machines employed at Day international flatten the sheets to tolerances of 10 microns and each require an extremely slow feed system to achieve the desired result.
"Due to the excellent performance of the two other systems we also recently upgraded the crucial final grinding machines with ZF clutches and brakes," explains Allan.
"The results were very favourable, with increased output, reduced wastage and costly downtime.
Other benefits became apparent as we could standardise on spares and the ZF ERM control interface allowed us to trouble shoot more quickly and easily than any other system we have used." The ZF range of brakes includes a high power series that offers (continuous) slip powers from 250 to 2,000W and peak capabilities of twice these figures.
With four different versions available offering torque capacities ranging from 0.08Nm to 520Nm, ZF's range of hysteresis clutches are especially useful for winding-on applications in packaging, labelling as well as paper or food packaging industries.
The range is backed-up by ZF, one of the most respected manufacturers of driveline technology in the world with production centres, partners and representatives on every continent.
In the industrial sector, ZF is at the forefront of developments, from individual units to complete systems solutions for all types of machinery and production units, including those used in robotic systems and factory automation. Request a free brochure from ZF Great Britain ...
• ZF Great Britain: contact details and other news
• Email this article to a colleague
• Register for the free Manufacturingtalk email newsletter
• Manufacturingtalk Home Page
Search the Pro-Talk network of sites
